Connecting usb backup to qnap nas12/31/2022 ![]() ![]()
To make doubly sure, ensure your QNAP NAS supports usb-hid, such as the TS-669-L listed under UPS support at the bottom of the page here. #CONNECTING USB BACKUP TO QNAP NAS MAC#Usb-hid is also what Mac computers require to connect to UPS which may be an indication as to its compatibility. When looking for a UPS check if the UPS device supports usb-hid. #CONNECTING USB BACKUP TO QNAP NAS SOFTWARE#You are best advised either to ask in the UPS topic at the QNAP Forum or contact QNAP Online Support directly before purchase.īeing linux based, QNAP software connects with usb-hid compatible UPS devices. If neither your NAS model nor the APC UPS model you are interested are listed, there's a strong possibility it still may work. Models listed in the Official QNAP UPS Compatibility List are included below for completeness. Particularly with APC UPSes, some of the UPSes have changed over time but retained the same model number, so it's important to check the SKU which uniquely identifies each model. The following is a list of various UPSes that have been reported as working by users at the UPS Compatibility List topic at the QNAP Forum. UPSes known to be working with QNAP NASes Unedited Copy from original ' User Reported Compatible Uninterruptible Power Supplies ' page #CONNECTING USB BACKUP TO QNAP NAS FULL#Battery capacity indicates full charge, but I have a few things plugged into it and it shows 2 minutes of protection. Manufacturer is correct, Model is detected as Belkin UPS. Reports correctly and both regular shutdown and 'auto-proection' mode works as intended. All systems shutdown gracefully as expected. This has been tested twice since setting this up. Have three (3) NAS systems: 2 - TVS-682 and 1 - TS-453 ProĬonnected one of the TVS-682 to the UPS via USB cable it was sensed automatically.Ĭonfigured this device as the UPS Master and the other two NAS systems as Slaves and all three now report a connection to the UPS. Reports in the Admin Panel with correct information. Remaining battery correctly displays, autoprotection and restart works correctly. NAS is detected correctly shortly after USB cable plugged in. VALUE 800EI-AU 800VA / 480W Line Interactive (Tower) Works fine, did a test turning power off at wall to the UPS and the TS-259 Pro+ NAS turned off 5 minutes later as setup without problem after running on the UPS battery. UPS Brand, Model, Power Status, Battery level and time remaining all reported inside QNAP UI (2Hr 08Min). ![]() I have added 8-port HP network switch and ADSL router to UPS and reported time is 128 minutes. NAS has 4 x 1.5TB drives in RAID 5 and reports 153 minutes available on battery. Remember to charge the battery first (8hrs as recommended by APC) before plugging it in and try using top left USB port (if it doesn't show up in the admin panel)ĪPC Back-UPS RS 550 LCD 550 Master Control (BR550GI)Ģ19P detects unit automatically, reported battery life is 38 minutes (connected: TS-219P w/2HDDs Samsung EcoGreen F4, Netgear WNDR3700 WiFi-Router, external WD USB HDD, cable modem, DECT phone)ĭetected, model reported fine. Supplier Part Description: BK650VA 230V ASEAN Gives 28 minutes, 7 seconds as the estimated battery life for the 419P. TS-419P estimates 1h:14m battery life on UPS normally, but on power cut this estimate drops to about 34m.Īutomatically detected by 419P. On test of power cut (unplugging UPS), the TS-419P shuts down as directed by the Administration interface. Still no power outage, so no actual function test yet.Ĥ19P successfully detects APC Back-UPS ES 450 unit. Works great, the only thing missing is it won't report the estimated protection time in the QTS UPS Settings.ĭetection working as it should. Should work on all Qnap models, all Salicru use same system I believe so good to go. Sees battery level, sees mains failure and actions your presets, nothing more needed, Great value Spanish company UPS. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |